#769 - RFQ Overview
kindly give me your technical and commercial offer for the attached file
This requirement was submitted on March 1, 2022, 12:00 AM
List of Materials/Services
Car overview
| # | Product Name | Quantity | Unit | Description |
|---|---|---|---|---|
| 1 | Special Bearings & Transmission Solutions | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 2 | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
|
| 3 | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
|
| 4 | Threaded Rods & Studs | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 5 | Pressure Relief Valves | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 6 | Ball Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 7 | Floating Ball Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 8 | Full Bore & Reduced Bore Ball Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 9 | Multi-Way Ball Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 10 | Trunnion Mounted Ball Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 11 | V-Port Ball Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 12 | Butterfly Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 13 | Concentric Butterfly Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 14 | Double Offset & Triple Offset Butterfly Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 15 | High-Performance Butterfly Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 16 | Check Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 17 | Dual Plate Check Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 18 | Lift Check Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 19 | Swing Check Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 20 | Tilting Disc Check Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 21 | Cryogenic Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 22 | Cryogenic Ball Valves | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 23 | Cryogenic Check Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 24 | Cryogenic Gate Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 25 | Cryogenic Globe Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 26 | Diaphragm Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 27 | Straight-Through Diaphragm Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 28 | Weir-Type Diaphragm Valves | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 29 | Gate Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 30 | Knife Gate Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 31 | Pressure Seal Gate Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 32 | Rising Stem & Non-Rising Stem Gate Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 33 | Wedge Gate Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 34 | Globe Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 35 | Angle Globe Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 36 | Pressure Seal Globe Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 37 | Y-Type & T-Type Globe Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 38 | Plug Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 39 | Lubricated Plug Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 40 | Multiport Plug Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 41 | Non-Lubricated Plug Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 42 | Pressure Relief & Safety Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 43 | Pilot-Operated Safety Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 44 | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
|
| 45 | Spring-Loaded Safety Valve | 30 | Pieces | Adjustable choke valve ( External sleeve )  Both sleeves in the external sliding and seat nozzle are made of solid Tungsten Carbide , which are abrasion and erosion resistance .  With the pressure – balancing bores in the external sliding sleeve , the stem will face the minimum load form downstream pressure .  With bean size indicator on the stem , the throttle bore can be observed .  Maximum orifice (3") bore.  The stem will be locked when tighten to the wing nut position so as to assure the selected flow rate maintained .  R.T.J ( R37) right angle , bolted bonnet , hand wheel Operation .  The orifice size is to be read the indicator scale .  Body , bonnet : Alloy steel . Specifications :  Basic Design and Test APl-6A  Working Pressure ( PSI ) 3000  Main Nominal Size ( in ) 4 -1 /16  Product Specification Level PSL2  Performance Requirement Level PR2  Material Class EE  End Connection Flanged  Working Temperature PU ( -29C° to 121 C° ) |
| 46 | Special Bearings & Transmission Solutions | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 47 | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
|
| 48 | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
|
| 49 | Threaded Rods & Studs | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 50 | Pressure Relief Valves | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 51 | Ball Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 52 | Floating Ball Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 53 | Full Bore & Reduced Bore Ball Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 54 | Multi-Way Ball Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 55 | Trunnion Mounted Ball Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 56 | V-Port Ball Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 57 | Butterfly Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 58 | Concentric Butterfly Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 59 | Double Offset & Triple Offset Butterfly Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 60 | High-Performance Butterfly Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 61 | Check Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 62 | Dual Plate Check Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 63 | Lift Check Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 64 | Swing Check Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 65 | Tilting Disc Check Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 66 | Cryogenic Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 67 | Cryogenic Ball Valves | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 68 | Cryogenic Check Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 69 | Cryogenic Gate Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 70 | Cryogenic Globe Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 71 | Diaphragm Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 72 | Straight-Through Diaphragm Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 73 | Weir-Type Diaphragm Valves | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 74 | Gate Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 75 | Knife Gate Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 76 | Pressure Seal Gate Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 77 | Rising Stem & Non-Rising Stem Gate Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 78 | Wedge Gate Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 79 | Globe Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 80 | Angle Globe Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 81 | Pressure Seal Globe Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 82 | Y-Type & T-Type Globe Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 83 | Plug Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 84 | Lubricated Plug Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 85 | Multiport Plug Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 86 | Non-Lubricated Plug Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 87 | Pressure Relief & Safety Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 88 | Pilot-Operated Safety Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
| 89 | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
|
| 90 | Spring-Loaded Safety Valve | 30 | Pieces | SURFACE SAFETY VALVE  Gate port through conduit slab ,full bore ,reverse acting gate , type line operated systems (a tapped hole provided in upstream flange)  valve size 4 1/16' x API 3000 PSI , Per API 6 A .  Ends flange RTJ,R37,according to ANSI B 16.5 .  Material class :EE,FOR sour gas and oil (H2S) meets nace MR 01-75 (body and bonnet : alloy steel , gate , stem and seat : 410 SS with hard face )  PSL :2,temp . rating : PU , PR :2 . VALVE C/W HYDRAULIC ACTUATOR OF THE FOLLOWING  Fail safe _ close design per API 6A.  Design Pressure is API 3000 PSI , working pressure range (200 -700 ) PSI .  Operated by flow line pressure range (200 – 700 ) PSI to compress the power spring .  Material class : EE , external pressure line , upper stem showing the position of the gate . VALVE C/W SENSING SYSTEM OF THE FOLLOWING * Max working pressure 3000 PSI , contain the following parts 1. Pilot pressure sensor suitable for working with pressure range ( 200–700 ) PSI , low range only ( can be setting manually at each point within this range ) . 2. Velocity check valve . 3. Needle valve 1/2' . Tubing 3/8 stainless steel . |
Chat on WhatsApp